Admin

17. The Fill Light of the Quad RGB Sensor Won't Work

1. Products
2. mBot Neo/mBot2

This guide applies to: mBot2 and mBot Neo.   Routine Check Refer to the quick steps below to rule out basic issues.   In a Nutshell   Possible Cause 1: The Fill Light isn't Configured in mBlock ...

• Edited July 18, 2023 01:52
• 1 follower
• 0 comments
• 0 votes

18. mBot2 Won't Detect Color Properly

1. Products
2. mBot Neo/mBot2

This guide applies to: mBot2 and mBot Neo.   Routine Check   In a Nutshell The color detection program doesn't recognize color correctly. This is usually related to the Quad RGB Sensor. What t...

• Edited July 18, 2023 01:52
• 1 follower
• 0 comments
• 1 vote

19. mBot2 Won't Do Line-Following

1. Products
2. mBot Neo/mBot2

This guide applies to: mBot2 and mBot Neo.   Routine Check Refer to the quick steps below to rule out basic issues.   In a Nutshell When your device won't perform line-following as expected. It's ...

• Edited September 15, 2023 10:22
• 2 followers
• 0 comments
• 8 votes

20. The Servo Motor Won't Work

1. Products
2. mBot Neo/mBot2

This guide applies to: mBot2 and mBot Neo.   Routine Check Refer to the quick steps below to rule out basic issues.   In a Nutshell Step by Step Possible Cause 1 The servo motor won't work due to...

• Edited August 01, 2023 08:52
• 1 follower
• 0 comments
• -1 votes

21. The Servo Is Blocked

1. Products
2. mBot Neo/mBot2

This article applies to: mBot2, and mBot Neo.   Routine Check Refer to the quick steps below to rule out basic issues. For details, please see this guide: Routines for Troubleshooting CyberPi ...

• Edited July 18, 2023 01:53
• 1 follower
• 0 comments
• -1 votes

22. CyberPi Displays Red Error Messages

1. Products
2. mBot Neo/mBot2

This guide applies to: mBot2, mBot Neo, and CyberPi.   Routine Check Refer to the quick steps below to rule out basic issues. For details, please see this guide:https://support.makeblock.com/hc/en...

• Edited July 18, 2023 01:53
• 1 follower
• 0 comments
• 0 votes

23. mBot2 Won't Turn Exactly as Expected

1. Products
2. mBot Neo/mBot2

This article applies to: mBot2/mBot Neo and CyberPi   Routine Check Refer to the quick steps below to rule out basic issues. For details, please see this guide: https://support.makeblock.com/hc/en...

• Edited July 18, 2023 01:53
• 1 follower
• 0 comments
• -4 votes

Case 1 - Hello World

1. Products
2. mBot Neo/mBot2

Part 1   Objective After you upload the program, the screen of CyberPi displays "Hello World". Part 2   Preparation CyberPi x 1 USB cable (Type-C) x 1 Computer with network access x 1 Conne...

• Edited April 07, 2023 03:43
• 5 followers
• 0 comments
• 36 votes

Case 2 - Control the LEDs

1. Products
2. mBot Neo/mBot2

Part 1   Objective After you upload the program, the RGB LEDs blink and light up one by one. Part 2   Preparation CyberPi x 1 USB cable (Type-C) x 1 Computer with network access x 1 Co...

• Edited April 07, 2023 03:54
• 2 followers
• 1 comment
• 18 votes

Case 3 - CyberPi says "Hi"

1. Products
2. mBot Neo/mBot2

Part 1   Objective After you upload the program and press button A, CyberPi says "Hi" to you. Part 2   Preparation CyberPi x 1 USB cable (Type-C) x 1 Computer with network access x 1 C...

• Edited April 07, 2023 03:55
• 1 follower
• 0 comments
• 15 votes