Admin

Make a Sprite Move on mBlock 5

1. Software & Apps
2. mBlock 5

Add a sprite 1. Click Sprites under the stage and click + add to add a sprite. Note: The default sprite is Panda, and you can click × in the upper right corner of the sprite to delete it. 2. Ch...

• Edited October 19, 2021 01:50
• 3 followers
• 0 comments
• 9 votes

Operators

1. Products
2. Halocode

  1. () + () Perform mathematical addition.   Example: When Halocode starts up, the LED ring will light up in the specified color order, and after 3 (1+2) seconds, go off. 2. () − () Perform ma...

• Created December 23, 2023 09:25
• 1 follower
• 0 comments
• -4 votes

9. How to View and Switch Between Preset Program and My Program

1. Products
2. mBot Neo/mBot2

  This guide applies to: mBot2, mBot Neo, and CyberPi.   Routine Check Refer to the quick steps below to rule out basic issues.   In a Nutshell   Step by Step   Related Knowledge https://s...

• Edited July 18, 2023 01:45
• 1 follower
• 0 comments
• -2 votes

Case 19 - Detecting Robot (I)

1. Products
2. Ultimate 2.0

Part 1   Objective Write a program to make the Detecting Robot move forward and backward. Part 2   Preparation Mechanical parts and electronic modules of Detecting Robot USB cable (Type-B...

• Edited April 07, 2023 03:13
• 1 follower
• 0 comments
• -1 votes

Add Sounds and Costumes on mBlock 5

1. Software & Apps
2. mBlock 5

On the Make a Sprite Move page, we describe how to make a sprite move. This page describes how to program the sprite to make sounds and how to change its costume.   Add a sound 1. Click Sounds on ...

• Edited October 19, 2021 01:50
• 2 followers
• 0 comments
• 0 votes

Control

1. Products
2. Halocode

  1. wait () seconds Wait for a specified period of time to run the script.   Example: When Halocode starts up, all the LEDs will light up green, and then go off after one second. 2. repeat () ...

• Created December 23, 2023 08:43
• 3 followers
• 1 comment
• 4 votes

10. How to Upload Programs to CyberPi or mBot2

1. Products
2. mBot Neo/mBot2

This guide applies to: mBot2, mBot Neo, and CyberPi.   In a Nutshell Learn more about the programs in CyberOS: How to View and Switch Between Preset Program and My Program How to Upload Programs t...

• Edited July 18, 2023 01:45
• 1 follower
• 0 comments
• -2 votes

Case 20 - Detecting Robot (II)

1. Products
2. Ultimate 2.0

Part 1   Objective Write a program to make the Detecting Robot follow the movements of your palm. Part 2   Preparation Mechanical parts and electronic modules of Detecting Robot USB cable...

• Edited April 07, 2023 03:17
• 2 followers
• 0 comments
• 0 votes

FAQs on mBlock 5

1. Software & Apps
2. mBlock 5

1. I want to install mBlock 5 on my PC. Are there any requirements on the CPU or memory of the PC? No specific requirements. You can install mBlock 5 as long as your PC runs an OSX system or Windo...

• Edited June 12, 2023 02:35
• 3 followers
• 1 comment
• -1 votes

Events

1. Products
2. Halocode

  1. when Halocode starts up When Halocode starts up, run the script.   Example: When Halocode starts up, the LED animation "spindrift" will be played. 2. when button is pressed When the button...

• Created December 23, 2023 08:35
• 1 follower
• 0 comments
• 0 votes