Admin

Program Codey Rocky with mBlock 5

1. Products
2. Codey Rocky

    This page describes how to use mBlock 5 to program Codey Rocky. 1. Download and install the required software 2. Connect Codey Rocky to mBlock 5 3. Start programming Codey Rocky When using mBl...

• Edited March 10, 2025 09:03
• 9 followers
• 1 comment
• 0 votes

Ultrasonic Sensor

1. Products
2. Halocode

  You can connect the [Ultrasonic Sensor] block of mbuild to Halocode, and make more creations.   1. ultrasonic sensor (1) distance to an object(cm) Reports the distance of an object detected by t...

• Created December 25, 2023 02:10
• 1 follower
• 0 comments
• 3 votes

Example — [Sprites] Create an Extension for Sprites

1. Software & Apps
2. mBlock 5 Extension Builder

This page uses an API-type extension as an example to describe how to use mBlock 5 Extension Builder. You can create an extension for sprites simply by a few steps. Our task is to enable the stage...

• Created June 13, 2023 07:02
• 2 followers
• 0 comments
• 0 votes

mLink Installation and Application

1. Software & Apps
2. mBlock 5

1. mBlock 5 fails to identify the COM port. What can I do? If mBlock 5 fails to identify the COM port when: 1. The CH340 driver is installed. 2. The COM port is displayed on Device Manager. If no ...

• Created May 23, 2023 07:42
• 4 followers
• 0 comments
• 0 votes

Program Codey Rocky with the mBlock App

1. Products
2. Codey Rocky

This page describes how to program Codey Rocky with the mBlock app on your smart device. Download and install the mBlock app Connect Codey Rocky to the mBlock app Write a program and run the prog...

• Edited March 29, 2023 03:05
• 1 follower
• 0 comments
• 3 votes

Case 15 - Smart night light

1. Products
2. CyberPi

Part 1   Objective After you upload the program, CyberPi detects the ambient light. When the brightness reaches a certain low value and there is sound around, the RGB LEDs on CyberPi light up and...

• Edited April 07, 2023 02:49
• 1 follower
• 0 comments
• -1 votes

Case 8 - Simulate collision avoidance with the ultrasonic sensor

1. Products
2. Ultimate 2.0

Part 1   Objective After you compile the program, you can make the motor stop or start based on the distance detected by the ultrasonic sensor. Part 2   Preparation MegaPi x 1 MegaPi RJ25 a...

• Edited April 06, 2023 10:21
• 1 follower
• 0 comments
• 0 votes

Case 7 - Marquee

1. Products
2. mBot Mega

Part 1   Objective After you upload the program, the RGB LEDs on the RGB module connected to pin A13 on MegaPi light up in turn, achieving the marquee effect. Part 2   Preparation MegaPi x 1 ...

• Edited April 07, 2023 08:23
• 1 follower
• 0 comments
• -1 votes

Case 10 - Self-made music

1. Products
2. mBot Ranger

Part 1  Objective After you upload the program, the buzzer on Auriga plays a short piece of Jingle Bells. Part 2  Preparation Auriga x 1 USB cable x 1 Computer with network access x 1 C...

• Edited April 04, 2023 03:20
• 2 followers
• 0 comments
• 5 votes

Dual Color Sensor

1. Products
2. Halocode

  You can connect the [Dual RGB Color Sensor] block of mbuild to Halocode, and make more creations.   1. dual color sensor (1) probe (1) detects color (white)? If the specified probe of the specif...

• Created December 25, 2023 02:07
• 1 follower
• 0 comments
• 0 votes